Murowash Murowash offers a finely grained, streak free flat finish with subtle colour variations. Second Finish Coat The surface should be dampened immediately prior to application. The surface should be inspected to ensure that it is properly adhering, free of oils, grease, loose particles, dirt, efflorescence, mould, moss or other foreign matter. Sand can be added to the Murobond mix in the ratio of 3 parts powder, up to 1. WSC is typically used in the final coat of Murobond only, however its use in both coats is beneficial in exposed situations or for single skin construction. Murobond creates a flat patina on interior walls which can show marks. Murowash offers a finely grained, streak free flat finish with subtle colour variations.
|License:||For Personal Use Only|
|iPhone 5, 5S resolutions||640×1136|
|iPhone 6, 6S resolutions||750×1334|
|iPhone 7, 7 Plus, 8, 8 Plus resolutions||1080×1920|
|Android Mobiles HD resolutions||360×640, 540×960, 720×1280|
|Android Mobiles Full HD resolutions||1080×1920|
|Mobiles HD resolutions||480×800, 768×1280|
|Mobiles QHD, iPhone X resolutions||1440×2560|
|HD resolutions||1280×720, 1366×768, 1600×900, 1920×1080, 2560×1440, Original|
Umrobond Flat shows good film integrity and adhesion preventing peeling. Cement Paint is a factory tinted product. The paints exceptionally resilient formula was developed with protection and performance in mind, making Murobond a wonderful way to enhance cement render, bagging, brickwork or any dimensionally stable surface.
Low Sheen and Low Sheen Grain both dry to a soft, eggshell finish.
Paint Types & Product Information
Where this is not practicable, sufficient material to complete an elevation should be ordered with any excess used as the first coat on the subsequent elevation. This incredibly versatile paint can be used both internally and externally. Internally sealing is not generally required. Refer to specific treatment for the appropriate substrate Cement render, bagged masonry Clay or concrete bricks or blocks, concrete and AAC Paperfaced plaster board and plaster Previously painted surfaces in sound condition Previously painted with a lime based coating Previously painted surfaces in unsound condition Other surfaces may be appropriate, contact your distributor for specification Ancillary Products W.
This is particularly important when hot, dry or windy conditions prevail or when overcoating previously painted, primed or sealed surfaces. If a smooth flat appearance is required some filling may be necessary.
It is recommended that sufficient material to complete the project be ordered where possible to eliminate possible colour variation. The mixed Murobond paint is applied by brush in a random pattern at a rate of approximately 6 sq. Different amounts may murobknd used in each coat with the lower amount typically being used in the second coat. Extremely important on exterior surfaces in hot weather.
To order please contact Murobond Head Office or your local stockist. Metal setting angles should not be used externally as corrosion of these will cause staining and damage to the paint film. Previously Painted with an Oil-based Paint Sand or chemically etch shiny surfaces to ensure adhesion and apply one coat of Murobond Primer.
Ideal for outdoor walls it can also be used indoors whether the tone is contemporary or traditional. The coat should be applied as thickly as possible while maintaining flow. WSC is typically used in the final coat of Murobond only, however its use in both coats is beneficial in extreme situations or for single skin construction. Following preparation of substrates as previously outlined Murobond Cement paint is applied as follows:.
Mineral Silicate Paint This paint is based on potassium silicate which chemically combines with masony surfaces to produce an extremely hard and durable finish.
The surface should be inspected to ensure that it is properly adhering, free of oils, grease, loose particles, dirt, efflorescence, mould, moss or other foreign matter. The mixed Murobond paint is applied in the same manner as the first coat.
Ideal for outdoor walls it can also be used indoors whether the tone is contemporary or traditional. For timbers containing tannin, we advise testing an area before proceeding to application as bleeding of tannin may cause visible staining. Allow 12 hours to dry between coats and before applying Murobond Cement Paint. Protection against mechanical abrasion should be provided for at least seven days after application.
Murobond Cement Paint – Murobond Superior Paints
If a flush finish is required, the wall should first be cement rendered. The Murobond powder is mixed with WSC Solution or water in the ratio 3 parts powder to 2 parts water to form a paint that is similar in consistency to cream.
Suitable for interior or exterior use Application by brush Supplied in powder form, mixed with water or WSC on site as required Two coat system Life span 7 — 10 years Suitable for residential or commercial projects More dramatic colour movement in darker colours Can be combined with a membrane system on parapet walls to provide waterproofing Addition of WSC Water Sheeting Conditioner to Murobond will significantly improve weathering on exposed surfaces such as parapets Allows walls to breath when applied over bare masonry Available in a wide range of standard colours — custom colours also made to order Addition of sand to achieve a light bagged effect and colour in one step More consistent results than coloured render systems — desired colour is easily achieved Not prone to show blockwork shadowing like render systems Location — interior and exterior.
The addition of clean sand to the mix creates an effect similar to bagging, reducing the visual impact of the jointing.
Mink – Murobond Superior Paints
Any lime remaining must umrobond firmly bound. To reduce this risk check weather reports, ensure thick film and mist spraying. It is recommended that large areas be divided by false expansion joints to reduce the working area to an area easily manageable by a contractor generally about 3m high by m long.